Diammable led drivers

-

 Dimmable led drivers

From: Huizhou Hi-zealed Electronic Co., Ltd

At present, the main dimming types on the market mainly include 0-10V, PWM, R, Triac, dali\dali2, WIFI, DMX512, switch dimming, and other dimming methods. The following is a brief introduction to the dimming methods that some customers ask more about.

1）0/1-10V dimmable

Constant voltage and constant current dimmable modes are optional. The dimming range is 0-100%. When connected with a 0-10V dimmer, the output current can be changed by 0-10V voltage change. With active PFC correction, EMC standard design, smooth dimming, seamless compatibility with 0-10V, 1-10V, 10VPWM dimmers and lighting control system. Although it can solve the problems of efficiency and PF, the dimmer needs to be changed, and the wiring cost is relatively high.

3in1(0-10/PWM/R) led driver


2）PWM

Through PWM wave on and off LED to change the forward current conduction time, in order to achieve brightness adjustment effect, dimming effect 0-100%. The method is based on the fact that the human eye is not sensitive enough to brightness flickering, so the loaded LED is bright and dark.

3）R

    The principle is to perform dimming of traditional incandescent lamps by changing the resistance value of the adjustable resistor, and the principle is to use the form of series voltage divider. The circuit of this dimming method is simple, the cost is low, there is no interference, and there will be no flickering during the dimming process.

4）Dali/Dali2

The characteristic of DALI is that the system terminal control can accurately control the lights point-to-point. Each LED light of DALI dimming will have an independent address, which can communicate in two directions. The system can identify the ID of each power supply, and the use is more flexible. This "What is the difference between DALI 1 and DALI-2?" article has written about the difference between Dali and Dali2.

Dali/dali2(+push function)


5）Triac

    Constant voltage and constant current dimming modes are available, and both leading edge and trailing edge dimming are supported. The working principle is to cut the waveform of the input voltage through the conduction angle to generate a tangential output voltage waveform, so as to reduce the power of the common load (resistive load). The advantages of thyristor dimming are high working efficiency, stable performance, and lower cost than 0-10V mode.

 

Triac dimmable led driver 


6）WIFI

Users can wirelessly control lighting fixtures by using mobile phones, APPs, etc., but this protocol is used in smart lighting, and the stability and penetration of the connection need to be solved.

Wifi（tuya)



Victoria Liang/Sales Department

Skype/Wechat: 13229150508/hizealed004

Watsapp/Tel:+86-132-2915-0508 

Add: 12th Jinling Road, Zhongkai Hi-tech Zone, Huizhou City, Guangdong, China,516006

Email: hzled07@gmail.com

Web:http://www.hzleddriver.com



评论

发表评论

此博客中的热门博文

Led Driver for tube light

-
图片
  Led Driver for tube light From:  www.hzleddriver.com          LED tube driver  is a LED driver power supply, it is the most important part of an LED tube lamp. improper choice, LED tube lamps can not play a performance, even can not be used normally.         Led Tube driver has two kinds built-in and external, the built-in is a long strip, that can be directly inserted into the semicircular tube inside. The built-in led driver is also divided into two types: isolated and non-isolated. Non-isolated means that there is a direct connection between the load end and the input end, and there is the risk of touch shock, especially when the load is high voltage.         The non-isolated type is most commonly used at present, which is directing step-down the power supply, as shown in Figure 1 ( HAD028CXN ). The non-isolated constant current led driver power supply has the advantages of simplicity and high index, an...
Read more »

How to judge the quality of Led Driver?

-
图片
  How to judge the quality of Led Driver? From:  www.hzleddriver.com   A few simple ways to identify the quality of an Led power supply: 1.  PFC (Power Factor Correction)         Now some countries will require at least PF>0.7, but not necessarily high PFC is good, but also consider the overall oblique wave (small), ripple (small), interference (low), because some manufacturers deliberately make the PFC very high but ignore the electromagnetic compatibility part. 2.  Conversion efficiency         Conversion efficiency, the value, and the stability of the deviation. For example, in the working voltage range of AC170-250V, you can try to debug it from 170V-250V. The voltage changes from low to high constantly, so that you can see on the power meter whether the fluctuation of "conversion efficiency, PFC" is large to prove its stability. 3.  Whether the temperature rise of the power supply is high       ...
Read more »

Choose a Led Driver for Street Light

-
图片
  Choose a Led Driver for Street Light From:  www.hzleddriver.com         With the development of the led lighting industry, the development of commercial led street lights is also getting faster and faster, and the advantages brought by led as an outdoor lighting source are becoming more and more prominent. Good power saving rate and lighting comfort make the development of led outdoor lighting more and the better. How to choose the right  led street light power supply , you need to consider a variety of factors. Here are the factors to consider when picking the best-led driver for the led street: 1. High-quality components         Street lights are in severe weather such as high temperature, high humidity, and lighting strikes, so the quality requirements for led drivers are very high. The quality of the led driver will affect the life of the led street lamp, and the quality of the led driver will be affected not only by good desi...
Read more »